Yep, our Rambler Pour Over is dishwasher safe so feel free to toss it in the top rack.

We recommend using it to brew hot drinks only.

Please do not microwave, or place on top of or in a fire. Personal injury can occur.

Yep. All Rambler® Products are food-safe and BPA free.

Standard dimensions are 3.5 inches (H) x 4.3 inches (W), while metric dimensions are 89mm (H) x 108mm (W).

You bet. In fact, all YETI® Drinkware and accessories are BPA free.

Yes, all YETI® Drinkware comes with a five-year warranty. For more information, please visit our Warranty Information page.

Unfortunately, the Rambler™ Pour Over is not available for customization.

No, but it is designed to sit on top of your existing Rambler® Drinkware.

Yes, the Rambler™ Pour Over will be available in the US, CA, EMEA, and AUS/NZ.

No. In fact, it’s designed to drip liquid into your drinkware.

Yes, like our other Rambler® Drinkware products, the Rambler™ Pour Over is double-wall insulated with 18/8 kitchen grade stainless steel.

The Rambler™ Pour Over will come with care and use instructions provided.

Our Rambler® 236 ml Stackable Cup is the suggested minimum size for the Rambler™ Pour Over.

The Rambler™ Pour Over fits on a variety of cups ranging from the Rambler® 236 ml Stackable Cup to the Rambler® 591 ml Tumbler depending on how much coffee you want to make.

We recommend using the Rambler® 414 ml Mug or 473 ml Stackable Cup to leave room for 355 ml of brewed coffee.

Since the Rambler™ Pour Over can only brew so much at a time, we suggest using the Rambler® 591 ml Tumbler or Travel Mug as your maximum cup size.

Yes, the Rambler™ Pour Over is one piece.

Pourover Recipe - Nowhere Coffee

15g of coffee + 250g of water for an 236 ml cup of brewed coffee.

Total brew time: 3 - 3 1/2 minutes

Step 1: Set up your Pourover

Place the YETI™ Pourover on top of your preferred Rambler® Drinkware. We recommend at least a 295 ml Tumbler or Mug. Fold the tabbed edge of the filter and insert it into your Pourover.

Step 2: Heat the water

Heat to just below boiling — about 202°F / 94.5°C.

Step 3: Rinse the filter

Rinse the filter with your hot water, and discard the rinse water from your cup.

Step 4: Grind coffee beans

Grind 15g of coffee beans to a medium grind and add to the filter.

Step 5: Bloom the coffee

Start a timer. Slowly pour 30g of water in a circular motion, making sure all of the coffee is wet. Let it bloom for 45 seconds and let the timer keep going.

Step 6: Pour water into two phases

Phase 1 - Pour while stirring the grounds until you reach 150g of water.

Phase 2 - Pour a little slower and more gently, aiming to reach the total brew weight (250g) in the next 30 seconds.

Step 7: Stir coffee

Give the soaked grounds a small stir in one direction and again in the other direction to release any grounds.

Step 8: Serve & enjoy

Once the coffee has fully brewed, remove the Pourover from your Tumbler or Mug and enjoy.

It all depends on how much you want to drink and how big your cup is. We recommend brewing a maximum of 591 ml.

The Rambler™ Pour Over will be available in four colours: Black, Navy, Rescue Red and White.

The Rambler™ Pour Over works best with any V60 conical filter.

The Rambler™ Pour Over is made of kitchen-grade 18/8 stainless steel.

While there aren’t any accessories for this product, the Rambler™ Pour Over works with any V60 filter and fits on top of most Rambler® Drinkware.

It’s always possible, but Black, Navy, Rescue Red, and White are the only colours available at launch.